Which Is The Best Hot Water Radiant Floor Heating System

Product Details
Model: RS15-6
Rated Power: 93/67/46W 
Outlet: 3/4 inch 
Max Flow: 36/29/20L/min
Rated Head: 20/16/13m
Volt/Freq: 110-120V/60Hz

Applications
Used in Suitable for city buildings, suburban villas, houses, water and pressurized with industrial equipment, air conditioning, boilers, solar circulating water, hot water circulating warm and so on

Advantages
1.High efficiency, high flow, leak-tightness, low consumption
2.No noise environmental protection, ease of installation
3.No leakage, low noise, environmental protection, aesthetics, ease of installation and so on
4.Built-in high sensitive electronic sensors with three-speed control

Performance Datas
1) Suitable for medium: Hot water and ethanol maximum ratio of 1:1
2) Performance: Liquid temperature range: 0℉ – +212℉Maximum working pressure 10bar
3) Ambient temperature: not higher than 40
4) Voltage: 110-120V(±10%) ,Frequency: 60Hz.
5) Motor: Protection class IP44 Insulation class F
6) Material: Stainless Steel, PP, ceramics
7) Mounting position: Shaft horizontal mounting
8) Pump settings: Single-phase pipeline pump 3 files manually controlled single-phase motor is not overloaded casting pump length 130 mm

The Heart of your Heating SystemRadiant Heat manifolds play a large part in heating systems. It allows for even distribution of supply water from the heat source to distribution lines that circulate hot water through the entire system. They can be used in a variety of applications ranging from radiant, hydronic, or snow-melt applications. The systems are made of adapters, end caps, and fittings that can be customized in a manifold depending on the application. A well-made manifold should distribute water efficiently and economically when the PEX tubing is sized properly. PEX manifolds reduce the need for soldering copper pipes, which prevents flames and chemicals getting into water lines causing problems. A Radiant PEX Manifold set can cover a large area depending on the branch. A 2-branch Radiant PEX Manifold Set can cover a maximum of 800 square feet to an 8-branch that can cover 1800-2200 square foot of floor.Our Radiant Floor Heating Manifold Set comes complete with:(1)- Manifold balance section Body with flow meters(1)- Manifold Isolation section Body with valves(2)- Mounting brackets (2)- Manifold Isolation ball valve with 1″ (inch) NPT Pipe Connection(2)- Stem thermometer on each Manifold Isolation ball valve(2)- Manifold end capsAlso includes 1/2″ Compression connectors-(* quantity varies by branch see below) CM1634-2 4pcsCM1634-3 6pcsCM1634-4 8pcsCM1634-5 10pcsCM1634-6 12pcsCM1634-8 16pcsCM1634-12 24pcsDon’t forget to “Add to Cart” now to start enjoying the durability of our Radiant Heat Manifolds!

Product Description

The pump is of the canned rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. The pump is characterized by ceramic shaft and radial bearings, carbon axial bearing, stainless steel rotor can and bearing plate, corrosion-resistant impeller, composite, PES, and cast iron pump housing. The motor is a 1-phase motor. No additional motor protection is required.

From the Manufacturer

Grundfos UPS15-58FC circulator pump (Grundfos# 59896341) incorporates a cast iron housing, three speed motor (Low/Med/High) and a built-in, removable check valve. Grundfos UPS15-58FC is among the most popular and most versatile circulator pump models on the market. Pump’s performance parameters cover nearly all traditional heating applications – from radiant and baseboards, to fan coils and zoning and many others. 3 speeds allow to set up the circulator pump in a way, that matches the system’s requirements, while wet rotor design allows it to be virtually silent while operating.

Conclusion

By our suggestions above, we hope that you can found hot water radiant floor heating system for you.Please don’t forget to share your experience by comment in this post. Thank you!